Doors wont open???

Daniel Radcliffe · Post by **Daniel Radcliffe** » Sun Jun 01, 2003 8:36 pm

OK, ive been through the doors tutorial with no problems, however now i have run into a problem with doors in that i cannot get them to work at all. Ive tried various settings on them from starting open (which they dont) to player activated opening/closing, ive also adjusted the angle the door should open too. The door is set to func_door, yet i still am unable to get the doors to open, i have tried to rebuild the doors, but still have had no luck with this.

Plz help.

Sonsai · Post by **Sonsai** » Sun Jun 01, 2003 9:54 pm

OK you made the door brush, but did you make the hinge brush? Make a thing strip in 4 grid view (press 4) and then make it a little wider than the door. Texture it the origin texture (common/origin) and then select the door and the hinge brush, then make them a func_door.

Zip · Post by **Zip** » Sun Jun 01, 2003 10:50 pm

Sonsai I think he's making a sliding door! If his door is a func_door it is a sliding door and therefore doesn't need the origin brush. If it is a func_rotatingdoor then he would need the origin brush.

So, Daniel, what door are you trying to make? You can send me your map with the door in and i'll have a look if you like

Daniel Radcliffe · Post by **Daniel Radcliffe** » Sun Jun 01, 2003 10:54 pm

Im trying both sliding and rotating door, on a couple of different buildings, and have now put hinges on all the doors.

Since I have done this i have been unable to load the map as i get this error come up in console:

ERROR: Func_door::SetSolidType entity at Xxxx YyyyZzzz with no BSP model.

I know what door it is yet cant see why this is happening.

tltrude · Post by **tltrude** » Mon Jun 02, 2003 3:34 am

You will get that error is an origin brush has no door brush as part of the entity. Do this:

1. Select both the door brush and the origin brush.

2. Goto selection and click on ungroup brush.

3. Highlight both brushes again and hit key N.

4. Double click on func_door or func_rotatingdoor.

5. Check to make sure both brushes have only one lable in the 2d window.

6. Set the angle of a rotating door to the direction players will face to open it.

It should work now. The origin brush and the door brush must be one entity. Using an origin brush moves the center point of an entity to the center of the origin brush.

Daniel Radcliffe · Post by **Daniel Radcliffe** » Mon Jun 02, 2003 8:09 am

Thx, that sorted the problem.

Daniel Radcliffe · Post by **Daniel Radcliffe** » Mon Jun 02, 2003 2:45 pm

Nope, the prob isnt sorted, its all back as it was, although some doors i seem to be able to walk through while they are closed.

This is damn irritating now

Daniel Radcliffe · Post by **Daniel Radcliffe** » Mon Jun 02, 2003 3:13 pm

NM, figured it out, problem is that im an idiot, i didnt join hinges properly

tltrude · Post by **tltrude** » Mon Jun 02, 2003 4:10 pm

You did good! At least you figured it out without sending your map to someone. That puts you one up on all the other new guys around here, he he. Now you need to figure out ladders and breakable windows!

Daniel Radcliffe · Post by **Daniel Radcliffe** » Mon Jun 02, 2003 11:16 pm

Ladders i already have figured out

and not looked at windows yet.

However i have a more minor irritant atm as i somehow managed to get my 3d view into a frameview and am unable to take it out again as i have no idea how i switched it to that view in the first place.

So if anyone knows the command for this then could you pleaselet me know where it is.

Thx

tltrude · Post by **tltrude** » Mon Jun 02, 2003 11:32 pm

It's the little eye icon. I use the one with no number, but I guess you can change it and change it back to pop the window back in. The popper outter has got to be one of those icons anyway. Or, try right clicking on the window title bar.

.Map :: MoHAA Mapping

Doors wont open???

Doors wont open???

origin

good work

eye